#AEON LABS Z STICK ADD DEVICE UPDATE#
#AEON LABS Z STICK ADD DEVICE SOFTWARE#
#AEON LABS Z STICK ADD DEVICE PC#
#AEON LABS Z STICK ADD DEVICE DOWNLOAD#

With the Z-Stick press and hold the button until the LED blinks fast, the stick is now in delete mode.

If the lock fails to add, try deleting it first. You can control the lock with the lock device in HomeSeer.

#AEON LABS Z STICK ADD DEVICE UPDATE#

Once the lock is added, press the lock and unlock button on the lock to update the status in HomeSeer. The lock should beep and the Schlage LED should blink green. On the lock enter your master code, then press the Schlage button, then 0 on the keypad. In HomeSeer click on Setup, then Interfaces, then click the Add Device button. If you are using a SmartStick, bring the lock close to your PC, or if your SmartStick is connected to a laptop, bring the laptop to the lock. The lock will beep and the Schlage LED should blink green indicating a successful add.

Click Import Devices and the lock should then add to HomeSeer. Insert the stick back into your HomeSeer system, start HomeSeer, click on Setup, then Interfaces, then the Manage button. The lock may beep and blink red, this is ok. The LED on the Z-Stick should go solid for a few seconds, indicating that the lock was added. At the lock, enter you master code, then press the Schlage button, then the 0 key.

Press and release the button on the stick so the blue LED blinks slowly, the stick is now in inclusion mode and is ready to add a Z-Wave device. If you are using the Z-Stick, shut down HomeSeer and remove the stick from your system and take it to the lock. As of this writing, our Z-Troller does not support the locks, but we expect an update to be available soon.

#AEON LABS Z STICK ADD DEVICE DOWNLOAD#

This update is available on our download page. The SmartStick needs to be updated with the 5.02 library if it is not already installed. As of this post, this is only the Z-Stick and the SmartStick.

#AEON LABS Z STICK ADD DEVICE PC#

* Z-Stick Z-Wave PC interface, or any other Z-Wave interface that contains version 5.02 or later of the Zensys library. Note also that no monthly fees are required to access your lock remotely. Note that the Schlage bridge is not required ( and not supported) when a lock is used with HomeSeer.

#AEON LABS Z STICK ADD DEVICE SOFTWARE#

This change requires updates to the HomeSeer software as well as the PC Z-Wave controller. This protocol encrypts all data that is sent and received by the door lock. Otherwise, you have successfully paired your Z-Wave device to your Z-Stick Gen5 network.With the release of the Schlage door locks:ДЄ new security protocol was added to Z-Wave. The LED on the Z-Stick Gen5 should blink blue rapidly for a bit, then become solid blue if successful, or solid red if unsuccessful. You've ensured that the Z-Wave device you want to add is completely factory reset, try pairing the device to your network.Д¤) Tap the Z-Stick Gen5 button, the LED should now blink blueДҐ) Tap the button on the Z-Wave Z-Wave device that you want to add. Now pair/include the device to your network The LED on the Z-Stick Gen5 should confirm a successful factory reset on a Z-Wave device by become solid blue.ДЈ) Now tap the button on the Z-Stick Gen5 to take it out of exclusion/unpair mode This ensures that all the network information in a Z-Wave device is completely wiped, this should be done after every failed inclusion process, or before you add a new device.Д ) Unplug your Z-Stick Gen5 from your PC if it is currently plugged in.ДЎ) Press and hold down the Z-Stick Gen5 button until it blinks yellow rapidlyДў) Tap the button on the Z-Wave device you want to factory reset If the steps below do not work, more than likely there are some issues with the device that you are trying to include, or the method of inclusion.ДЇirst Do an Exclusion or Unpair to a Z-Wave device (this also factory resets products) Make sure that the Z-Stick Gen5 and the Z-Wave device you are attempting to include are running the same network: Sometimes the inclusion process fails and there are a few troubleshooting steps that you can take to ensure the maximum success for during the inclusion process. Z-Stick Gen5 (ZW090) Cannot Add/Include a device to Z-Stick Gen5 (Troubleshooting)

Aeon labs z-stick add device